#ifndef __PSTWO_H
#define __PSTWO_H

#include "board.h"
/*********************************************************
Copyright (C), 2015-2025, YFRobot.
www.yfrobot.com
File：PS2驱动程序
Author：pinggai    Version:1.1     Data:2015/10/20
Description: PS2驱动程序
             增加功能：
			 1、软件设置“红灯模式”、“绿灯模式”，并可以设置“保存”，通过手柄“模式按键”无法改变
			 2、设置手柄震动：通过数值的设置，改变左侧大震动电机震动频率。
			                  通过数值的设置，开关右侧小震动电机。
History:  
V1.0: 	2015/05/16
1、手柄解码，识别按键值，读取模拟值。       
**********************************************************/	 
#if 0
#define DI   (Board::get()->getDIState(_JS_DAT))           //PB12  输入

#define DO_H (Board::get()->setDOState(_JS_CMD, 0))        //命令位高
#define DO_L (Board::get()->setDOState(_JS_CMD, 1))        //命令位低

#define CS_H (Board::get()->setDOState(_JS_CS, 0))       //CS拉高
#define CS_L (Board::get()->setDOState(_JS_CS, 1))       //CS拉低

#define CLK_H (Board::get()->setDOState(_JS_CLK, 0))      //时钟拉高
#define CLK_L (Board::get()->setDOState(_JS_CLK, 1))      //时钟拉低
#else
#include <stm32f10x.h>

#define BITBAND(addr, bitnum) ((addr & 0xF0000000)+0x2000000+((addr &0xFFFFF)<<5)+(bitnum<<2)) 
#define MEM_ADDR(addr)  *((volatile unsigned long  *)(addr)) 
#define BIT_ADDR(addr, bitnum)   MEM_ADDR(BITBAND(addr, bitnum)) 
#define GPIOA_ODR_Addr    (GPIOA_BASE+12) //0x4001080C
#define GPIOA_IDR_Addr    (GPIOA_BASE+8) //0x40010808 
#define PAout(n)   BIT_ADDR(GPIOA_ODR_Addr,n)  //输出 
#define PAin(n)    BIT_ADDR(GPIOA_IDR_Addr,n)  //输入


#define DI   PAin(4)           //PB12  输入

#define DO_H PAout(5)=1        //命令位高
#define DO_L PAout(5)=0        //命令位低

#define CS_H PAout(0)=1       //CS拉高
#define CS_L PAout(0)=0       //CS拉低

#define CLK_H PAout(1)=1      //时钟拉高
#define CLK_L PAout(1)=0      //时钟拉低
#endif

//These are our button constants
#define PSB_SELECT      1
#define PSB_L3          2
#define PSB_R3          3
#define PSB_START       4
#define PSB_PAD_UP      5
#define PSB_PAD_RIGHT   6
#define PSB_PAD_DOWN    7
#define PSB_PAD_LEFT    8
#define PSB_L2          9
#define PSB_R2          10
#define PSB_L1          11
#define PSB_R1          12
#define PSB_GREEN       13
#define PSB_RED         14
#define PSB_BLUE        15
#define PSB_PINK        16

#define PSB_TRIANGLE    13
#define PSB_CIRCLE      14
#define PSB_CROSS       15
#define PSB_SQUARE      16

//#define WHAMMY_BAR		8

//These are stick values
#define PSS_RX 5                //右摇杆X轴数据
#define PSS_RY 6
#define PSS_LX 7
#define PSS_LY 8

extern unsigned char Data[9];
extern unsigned short MASK[16];
extern unsigned short Handkey;

void PS2_Init(void);
unsigned char PS2_RedLight(void);   //判断是否为红灯模式
void PS2_ReadData(void); //读手柄数据
void PS2_Cmd(unsigned char CMD);		  //向手柄发送命令
unsigned char PS2_DataKey(void);		  //按键值读取
unsigned char PS2_AnologData(unsigned char button); //得到一个摇杆的模拟量
void PS2_ClearData(void);	  //清除数据缓冲区
void PS2_Vibration(unsigned char motor1, unsigned char motor2);//振动设置motor1  0xFF开，其他关，motor2  0x40~0xFF

void PS2_EnterConfing(void);	 //进入配置
void PS2_TurnOnAnalogMode(void); //发送模拟量
void PS2_VibrationMode(void);    //振动设置
void PS2_ExitConfing(void);	     //完成配置
void PS2_SetInit(void);		     //配置初始化

#endif